1/8/2024 0 Comments Midipipe for mac![]() ![]() Connect one adapter to the hub, one to the other USB adapter. These usually have two 5-pin male connectors, one for MIDI out, one for MIDI in. You could get two USB to 5-pin MIDI adapters. I was using a straight forward usb to midi cable. Connecting by BT MIDI in AUM does work, but it's more fiddly than I'd said: could get a second usb to midi Someone else may have the best solution for this. There will be some lag, and the messages will be merged, only distinguishable by MIDI channel number. You might be able to route your controllers to Network MIDI using Audiobus, AUM, or MIDIFire, then connect the second iPad to Network MIDI. Someone else may have the best solution for said: computer, it behaves as a slave, responding to commands from the master, e.g. The USB port on the hub that you tried is a slave port, and your second iPad wants to be a master.Įdit: When you connect an iPad to a USB master, e.g. That's why most USB cables have different connectors on each end. This doesn't work because USB is a master-slave protocol, one master, many slaves. Why doesn't this work, and is there some other way to do what I want? I had imagined they would do so if I plugged the second iPad into the USB hub with a USB-A to USB-A cable and the old (unpowered) CCK, but they don't. I would like all the MIDI controllers to also show up on the second iPad. I'll try to check back for troubleshooting.I have two iPad Pros (2017) and I have all my MIDI controllers connected to one of them using the USB3 CCK and a powered USB hub. ( and contain some good info) If you didn't see it, reread this and try again. Then you're on to mapping, which is explained elsewhere in this forum, so I won't. You should see "X-CCXX" appear in the space (Xs are numbers). ![]() ) At this point, you should be able to open Virtual DJ, click on Mapping under settings, click on "Simple MIDI Wrapper" then the "Key Learn" button. Set MidiPipe Input to "DSMidiWifi-out" and MiDiPipe Output to "IAC Bus 1." ( *NOTE* - in MidiPipe you have to drag the item from the left window to the right window to activate the input/output. (*OSCulator note - you should see the buttons in the OSCulator file light up when you move the sliders/knobs/buttons in Touch OSC ) For DJ Control, open "DSMidiWifi" (runs silently in the background) and MidiPipe. Launch MidiPipe and set the input to "MidiPipe Input 1" and output to "IAC Bus 1." Set the output in OSCulator (under parameters>I/O) and make sure "MidiPipe Output 1" is checked. If you go with OSC, start up OSCulator and load the matching MIDI CC map (believe they came with the OSCulator ). You'll need to enter the IP address of your MAC in the app setting so it links to your computer. Programs Required: - Virtual DJ (I was using 7.x) - Android App (I used TouchOSC and DJ Control, both free apps on the Market, DJ Control has an ad-free version for $1.99) - OSCulator ( shareware, easier - ) - OR - qosc ( needs Quartz Composer dev software ) - DSMidiWifi (available here, ) - MidiPipe (the brilliant solution, mad props! - ) Obviously, you also need Wifi access. ![]() I'm assuming you can figure out the basics for each program, just noting the things you might miss along the way. I figured there had to be a way to loop internally, and there was. I attempted to rout out-in through a USB MIDI interface, but I think either the software of hardware was killing the loop. The key issue with OSC-style support and Virtual DJ was the inability to grab the MIDI signal internally. I looked around a bit before figuring a lot of this out for myself. With the increased presence of Android phones and tablets, this should come in handy soon, if you haven't already tried and failed. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |